Adsl Modem Ve Port Açmak.. Emule-Kazaa-Torrent..2

**Prof. Dr. Sinsi** · 09-08-2012

D-LINK Modemlerde Port açmak

DI-514, DI-524, DI-604, DI-614+, DI-624, DI-704P (revC), DI-704UP, DI-754, DI-764, DI-774, and DI-784

Step 1 Open your web browser and enter the IP address of your D-Link router (192

168

0

1)

Enter username (admin) and your password (blank by default)

Step 2 Click on the Advanced tab at the top and then click Virtual Server on the left side

Step 3 Check Enabled to activate entry

Step 4 Enter a name for your virtual server entry

Step 5 Next to Private IP, enter the IP address of the computer on your local network that you want to allow the incoming service to

Step 6 Choose Protocol Type - either TCP, UDP, or both

If you are not sure, select both

Step 7 Enter the port information next to Private Port and Public Port

The private and public ports are usually the same

The public port is the port seen from the WAN side, and the private port is the port being used by the application on the computer within your local network

Step 8 Enter the Schedule information

Step 9 Click Apply and then click Continue

For DI-704P (revB), DI-707P, DI-714P+, DI-804HV, DI-808HV, and DI-824VUP users:

Step 1 Open a web browser and enter the IP address of your router (192

168

0

1)

Enter admin for your username and then your password (blank by default)

Step 2 Click on the Advanced tab and then Virtual Server on the left side

Step 3 Enter the following information:

Check the box next to Enable
Next to Service Ports, enter the port or range of ports you want to open
Next to Service IP, enter the IP address of the computer you want to open the port to
Click Always next to Schedule or enter the time frame that you want

Step 4 Click Apply and then click Restart to save your changes

For DI-704, DI-704P (rev A), DI-707, DI-711, DI-713, and DI-713P users:

Step 1 Open your web browser and enter the IP address of the router (192

168

0

1)

Enter user name (admin) and your password (blank by default)

If there is only 1 box, enter admin

Step 2 Click on Advanced at the bottom and then click Virtual Server

Step 3 Create a new entry:

Enter the port or range of ports you want to open in the box under Service Ports
Enter the IP address of the computer you want to open the ports to
Check the box under Enable

Step 4 Click Save and then click Reboot

2

Emule ayarlari

You must open ports on your router to allow incoming traffic while using eMule

eMule uses three ports*:
4662 (TCP)
4672 (UDP)
4711 (TCP)

* To prevent getting a low ID (Firewalled), open additional TCP ports between 4661 and 4665 Also, limit the number of connections in the eMule software You may need to change the TCP Clientport to something other than 4662

For the DI-5xx, DI-6xx, DI-704P (revC), DI-704UP, DI-754, DI-764, DI-774, DI-784, DI-804HV, DI-808HV, and DI-824VUP:

Step 1 Open your web browser and enter the IP address of your router (192

168

0

1)

Enter username (admin) and your password (leave blank)

Step 2 Click on Advanced and then click Virtual Server

Step 3 Create a new entry: Click Enabled

Enter a name (emule1)

Private IP - Enter the IP address of the computer you are running eMule from

Select TCP for Protocol Type
Enter 4662 for both Private Port and Public Port
<LI>Click Always or set a schedule

Step 4 Click Apply and then Continue

Step 5 Repeat steps 3 and 4 but name it emule2, select UDP for Protocol Type, and enter 4672 for both Private Port and Public Port

Step 6 Repeat steps 3 and 4 but name it emule3, select TCP for Protocol Type, and enter 4711 for both Private Port and Public Port

Note: If the screenshots look different (DI-604), then you have the European version of your router which D-Link USA does not support

For the DI-704P (revB) and DI-707P:

Step 1 Open a web browser and enter the IP address of your router (192

168

0

1)

Enter admin for your username and then your password (blank by default)

Step 2 Click on the Advanced tab and then Virtual Server on the left side

Step 3 Enter the following information:

Check the enable box
Next to Service Ports, enter 4661-4665
Next to Server IP, enter the IP address of the computer you want to run eMule from
Click Always or set a schedule
Click Apply and then click Restart to save changes

Step 4 Repeat step 3 but enter 4672 for the service port

Step 5 Repeat step 3 but enter 4711 for the service port

Step 6 Click Save and then Restart

For the DI-704P (revA), DI-704, DI-707, DI-711, DI-713, and DI-713P:

Step 1 Open your web browser and enter the IP address of the router (192

168

0

1)

Enter user name (admin) and your password (blank by default)

If there is only 1 box, enter admin

Step 2 Click on Advanced at the bottom and then click Virtual Server

Step 3 Create a new entry:

Enter 4661-4665 in the box under Service Ports
Enter the IP address of the computer you want to run eMule from
Check the box under Enable
In the next box down, enter 4672 under Service Ports
Enter the IP address of the computer you want to run eMule from
Check the box under Enable
In the next box down, enter 4711 under Service Ports
Enter the IP address of the computer you want to run eMule from
Check the box under Enable

Step 4 Click Save and the click Reboot

detaylı bilgi için link aşağıda
http://support

dlink

com/faq/search

rt%20forwarding

09-08-2012	#4
Prof. Dr. Sinsi	Adsl Modem Ve Port Açmak.. Emule-Kazaa-Torrent..2 D-LINK Modemlerde Port açmak DI-514, DI-524, DI-604, DI-614+, DI-624, DI-704P (revC), DI-704UP, DI-754, DI-764, DI-774, and DI-784 Step 1 Open your web browser and enter the IP address of your D-Link router (19216801) Enter username (admin) and your password (blank by default) Step 2 Click on the Advanced tab at the top and then click Virtual Server on the left side Step 3 Check Enabled to activate entry Step 4 Enter a name for your virtual server entry Step 5 Next to Private IP, enter the IP address of the computer on your local network that you want to allow the incoming service to Step 6 Choose Protocol Type - either TCP, UDP, or both If you are not sure, select both Step 7 Enter the port information next to Private Port and Public Port The private and public ports are usually the same The public port is the port seen from the WAN side, and the private port is the port being used by the application on the computer within your local network Step 8 Enter the Schedule information Step 9 Click Apply and then click Continue For DI-704P (revB), DI-707P, DI-714P+, DI-804HV, DI-808HV, and DI-824VUP users: Step 1 Open a web browser and enter the IP address of your router (19216801) Enter admin for your username and then your password (blank by default) Step 2 Click on the Advanced tab and then Virtual Server on the left side Step 3 Enter the following information: Check the box next to Enable Next to Service Ports, enter the port or range of ports you want to open Next to Service IP, enter the IP address of the computer you want to open the port to Click Always next to Schedule or enter the time frame that you want Step 4 Click Apply and then click Restart to save your changes For DI-704, DI-704P (rev A), DI-707, DI-711, DI-713, and DI-713P users: Step 1 Open your web browser and enter the IP address of the router (19216801) Enter user name (admin) and your password (blank by default) If there is only 1 box, enter admin Step 2 Click on Advanced at the bottom and then click Virtual Server Step 3 Create a new entry: Enter the port or range of ports you want to open in the box under Service Ports Enter the IP address of the computer you want to open the ports to Check the box under Enable Step 4 Click Save and then click Reboot 2 Emule ayarlari You must open ports on your router to allow incoming traffic while using eMule eMule uses three ports: 4662 (TCP) 4672 (UDP) 4711 (TCP) To prevent getting a low ID (Firewalled), open additional TCP ports between 4661 and 4665 Also, limit the number of connections in the eMule software You may need to change the TCP Clientport to something other than 4662 For the DI-5xx, DI-6xx, DI-704P (revC), DI-704UP, DI-754, DI-764, DI-774, DI-784, DI-804HV, DI-808HV, and DI-824VUP: Step 1 Open your web browser and enter the IP address of your router (19216801) Enter username (admin) and your password (leave blank) Step 2 Click on Advanced and then click Virtual Server Step 3 Create a new entry: Click Enabled Enter a name (emule1) Private IP - Enter the IP address of the computer you are running eMule from Select TCP for Protocol Type Enter 4662 for both Private Port and Public Port <LI>Click Always or set a schedule Step 4 Click Apply and then Continue Step 5 Repeat steps 3 and 4 but name it emule2, select UDP for Protocol Type, and enter 4672 for both Private Port and Public Port Step 6 Repeat steps 3 and 4 but name it emule3, select TCP for Protocol Type, and enter 4711 for both Private Port and Public Port Note: If the screenshots look different (DI-604), then you have the European version of your router which D-Link USA does not support For the DI-704P (revB) and DI-707P: Step 1 Open a web browser and enter the IP address of your router (19216801) Enter admin for your username and then your password (blank by default) Step 2 Click on the Advanced tab and then Virtual Server on the left side Step 3 Enter the following information: Check the enable box Next to Service Ports, enter 4661-4665 Next to Server IP, enter the IP address of the computer you want to run eMule from Click Always or set a schedule Click Apply and then click Restart to save changes Step 4 Repeat step 3 but enter 4672 for the service port Step 5 Repeat step 3 but enter 4711 for the service port Step 6 Click Save and then Restart For the DI-704P (revA), DI-704, DI-707, DI-711, DI-713, and DI-713P: Step 1 Open your web browser and enter the IP address of the router (19216801) Enter user name (admin) and your password (blank by default) If there is only 1 box, enter admin Step 2 Click on Advanced at the bottom and then click Virtual Server Step 3 Create a new entry: Enter 4661-4665 in the box under Service Ports Enter the IP address of the computer you want to run eMule from Check the box under Enable In the next box down, enter 4672 under Service Ports Enter the IP address of the computer you want to run eMule from Check the box under Enable In the next box down, enter 4711 under Service Ports Enter the IP address of the computer you want to run eMule from Check the box under Enable Step 4 Click Save and the click Reboot detaylı bilgi için link aşağıda http://supportdlinkcom/faq/searchrt%20forwarding